PYLE Audio Printer PP5600 User Manual

PP5600 SERIES  
POS PRINTER  
USER’S MANUAL  
Rev.: A  
Do not connect cables in ways other than those mentioned  
in this manual. Different connections may cause equipment  
damage and burning.  
Never attempt to repair this product yourself.  
Improper repair work can be dangerous.  
 
Table Of Contents  
BEFORE STARTED . . . . . . . . . . . . . . . . . . . . . . .1 -- 1  
CONGRATULATION . . . . . . . . . . . . . . . . . . . . . .1 -- 1  
PRODUCT BRIEFING . . . . . . . . . . . . . . . . . . . . . 1 -- 1  
Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -- 1  
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 -- 2  
MODELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 -- 3  
UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 -- 3  
OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 -- 4  
IMPORTANT TIPS . . . . . . . . . . . . . . . . . . . . . . . . 1 -- 5  
MAIN PARTS ON THE EXTERIOR . . . . . . . . .1 -- 6  
INDICATORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 -- 7  
QUICK START-UP . . . . . . . . . . . . . . . . . . . . . . . . 2 -- 1  
CONNECTING CABLES . . . . . . . . . . . . . . . . . . . 2 -- 1  
Serial connection . . . . . . . . . . . . . . . . . . . . . . 2 -- 1  
Parallel connection . . . . . . . . . . . . . . . . . . . .2 -- 1  
Peripheral connection . . . . . . . . . . . . . . . . . . 2 -- 1  
Power connection . . . . . . . . . . . . . . . . . . . . . 2 -- 2  
LOADING / REPLACING RIBBON CASSETTE . . . .  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 -- 2  
LOADING PAPER . . . . . . . . . . . . . . . . . . . . . . . . .2 -- 4  
SELF TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 -- 5  
SPECIAL ADJUSTMENTS . . . . . . . . . . . . . . . . .2 -- 6  
Paper near end sensor . . . . . . . . . . . . . . . . . .2 -- 6  
DIP switch setting . . . . . . . . . . . . . . . . . . . . .2 -- 6  
MAINTENANCE GUIDES . . . . . . . . . . . . . . . . . . . .3 -- 1  
MAINTENANCE GUIDE LINES . . . . . . . . . . . . 3 -- 1  
GENERAL CLEANING . . . . . . . . . . . . . . . . . . . .3 -- 1  
TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . .3 -- 1  
General problems . . . . . . . . . . . . . . . . . . . . .3 -- 1  
i
 
Printing problems . . . . . . . . . . . . . . . . . . . . .3 -- 2  
Paper jam problems . . . . . . . . . . . . . . . . . . .3 -- 3  
Auto cutter problems . . . . . . . . . . . . . . . . . . 3 -- 3  
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . .4 -- 1  
PRINTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 -- 1  
PAPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 -- 1  
RIBBON CASSETTE . . . . . . . . . . . . . . . . . . . . . .4 -- 2  
POWER ADAPTOR . . . . . . . . . . . . . . . . . . . . . . . 4 -- 2  
ii  
 
I. BEFORE STARTED  
A. CONGRATULATION  
You have made a very wise decision by purchasing the easy  
loading; high performance; high reliability 9 pin dot matrix  
impact printer Aura PP5600 series of Posiflex products. This  
series of printers has been elegantly designed for a Point-Of-Sale,  
kitchen & kiosk application. The manufacturer of this printer not  
only wishes to take this opportunity to congratulate your smart  
investment on buying this printer but also likes to express the  
wishes for your prosperous future by using it.  
B. PRODUCT BRIEFING  
1. DESCRIPTIONS  
The Aura PP5600 series printer is a stream-lined low profile  
40 column 9 pin dot matrix easy loading impact printer designed  
to fit the Posiflex POS system perfectly well and also for other  
POS printing applications. The Aura PP5600 series printer serves  
the stand-alone desktop application. The print mechanism applied  
in this printer series is remarkably reliable. as well as the wall  
mount application  
The Aura PP5600 series utilizes friction type paper feed  
mechanism and supports two types of interface input in one  
machine through semi-automatic detection on which type of cable  
connected. The interfaces are RS232 for serial interface and  
Centronics mode for parallel interface. Cabinet color is selectable  
between beige and charcoal.  
The Aura PP5600 supports an optional guillotine type auto  
cutter for paper partial cut and a standard manual cut mechanism.  
1 - 1  
 
It even supports some enhancement capability for reminder  
function to persons around. It can be used to drive a separately  
purchased kitchen bell for such reminder function in noisy  
environment. This printer also supports application in different  
countries of various kinds of power systems by changing the  
power cord to the power adaptor. The Aura PP 5600 series also  
supports an optional journal paper roll rewinder when non-carbon  
copy paper roll is used.  
2. Features  
·
·
·
·
·
·
·
Dot matrix 9 pin printer head  
Bi-directional printing with logic seeking  
Friction type paper feed  
40 columns for 16.9 CPI  
Print on ordinary paper or up to 3-fold non-carbon copy paper  
DC 24V powered  
Selectable parallel or serial (RS232C) interface by detection  
on cable change and DIP switch settings  
·
·
5 character code pages for code range 80h to FFh supported:  
USA & Europe PC437, PC850, PC860, PC863, PC865  
15 international character sets of a dozen characters each  
within code range 20h to 7Fh supported: USA, France,  
Germany, England, Denmark, Sweden, Italy, Spain, Japan,  
Norway, Denmark II, Spain II, Latin America, Korea, Croatia  
·
·
Versatile print function as emphasized printing and  
underlining set by software print commands  
About 20KB input buffer available enabling simultaneous  
printing and data receiving  
1 - 2  
 
·
·
·
Supports Posiflex kitchen bell drive when used as kitchen  
printer  
Hardware hand shaking in serial interface through DIP switch  
selection  
Manual paper cut mechanism for PP5600D or guillotine type  
auto cutter plus manual cut mechanism for PP5600B  
·
·
Supports ESC command  
Dimension: 228 mm (l) x 158 mm (w) x 140 mm (h)  
C. MODELS  
PP5600D – with manual cutter  
PP5600B – with auto cutter  
PP5600A – with take up rewinder and auto cutter  
D. UNPACKING  
Followings are items you may find when you carefully  
unpack the carton that delivers Aura PP5600 series printer. If  
there is any discrepancy or problem, contact your dealer  
immediately. Be sure to save the packing materials in case the  
printer needs to be shipped at some point in the future.  
ƒ
The printer itself.  
Test paper roll 76 mm in width.  
Ribbon cartridge  
One of the interface cables:  
a Serial cable with 9 pin D sub Female to 9 pin D sub Male  
connectors  
b Parallel cable with 25 pin D sub Male to 25 pin D sub  
Female connectors  
1 - 3  
 
Length of the interface cable depends on whether the order  
includes the power adaptor. When power adaptor is included, the  
interface cable is 6 ft long for stand alone application. When the  
power adaptor is not included in the order, the interface cable is a  
shorter one for integrated application in Posiflex POS system.  
One of the power sources:  
a Power adaptor + power cord (depend on country type  
ordered).  
b Power supply cable (when no power adaptor ordered)  
This printer power supply cable is used to supply power to  
the printer from the PB or PST series of Posiflex POS system.  
This User’ s Manual  
E. OPTIONS  
The underlined items below must be well defined in order, they  
can not be field added or changed.  
·
·
·
·
·
·
·
·
·
Paper near end sensor  
Special language selection  
Case color option  
Inked ribbon cartridge  
Kitchen bell  
Guillotine type auto paper cutter  
Journal paper roll rewinder  
Wall mount kit  
Paper roll  
1 - 4  
 
F. IMPORTANT TIPS  
Place the printer on a sturdy, level surface.  
Choose a place that is well ventilated and free from direct  
sunshine and excessive heat, dust, smoke or fume.  
Never attempt to disassemble or modify this product.  
Unauthorized interior access voids product warranty.  
Do not connect a telephone line to the peripheral port.  
Otherwise, both printer and telephone line may be  
damaged.  
Do not touch the print head after printing.  
It can become very hot.  
Use a grounded AC power outlet. Use only the power cord  
and power adaptor furnished with the printer.  
Do not use a power outlet of a circuit shared with any  
equipment that causes great electrical noise, such as  
motors.  
Do not use a power outlet of a circuit shared with any  
equipment that uses a lot of power, such as a copier or a  
coffee maker.  
Do not set any liquid or drinks such as coffee on the  
printer case.  
Do not touch any connector contacts to avoid  
possible electrostatic damage.  
Ideal room temperature is from 5º C to 40º C. Ideal humidity  
is from 20% to 85% RH (no condensation).  
1 - 5  
 
G. MAIN PARTS ON THE EXTERIOR  
Top Cover  
Manual  
Cutter  
Power LED  
Error LED  
Paper Out  
LED  
FEED Button  
PP5600B  
PP5600D  
Bottom Cover  
Power Switch  
Parallel Connector  
Power Connector  
Rear View  
Peripheral Connector  
Serial Connector  
Frame Ground  
Screws  
Bottom View  
Setup Window  
Window Plate Screw  
1 - 6  
 
Interior View  
Auto Cutter  
Lift Tab  
Ribbon Cassette Area  
Paper Guide Roller  
Paper Roll Area  
Indicators  
·
·
·
Power LED: green  
Error LED: red  
Paper Out LED: red  
1 - 7  
 
 
II. QUICK START-UP  
A. CONNECTING CABLES  
1. Serial connection  
All the external connectors are in the recessed area at the  
rear bottom. The serial connector is a 9 pin D sub Female  
connector at the right in the picture above. Apply the male  
connector of RS232 cable to this port for serial application. Please  
note that when serial connection is used, there must be no cable  
connection at the parallel port on the printer. The default protocol  
used in serial connection is 9600 bps, none parity check, 8 data  
bits, 1 stop bit.  
2. Parallel connection  
The parallel connector is a 25 pin D sub Male connector at  
the leftmost location in the connector area. Apply the female end  
of the parallel cable at this port for parallel application. Please  
note that when parallel connection is used, there must be no cable  
connection at the serial port on the printer. Please also check the  
DIP switch settings inside the service window at bottom side of  
the printer following instructions later in this chapter.  
3. Peripheral connection  
The peripheral controller is a RJ11 jack near the serial  
connector. With use of Posiflex cash drawer cable 20863018001  
(CCBLA-180-1), this port can control a Posiflex cash drawer  
CR3100 or CR3200 or CR4000 or CR4210. If a Posiflex special  
2 - 1  
 
split cable 20867023800 (CCBLA-238) is used instead, this port  
can control two cash drawers of above models.  
When the printer is used as a kitchen printer, please use this  
port for kitchen bell connection instead.  
4. Power connection  
The power connector is a 3 pin jack between the peripheral  
connector and the parallel connector. Either a Posiflex supplied  
power adaptor or a printer power cable from a Posiflex POS  
system can be connected to this connector to supply power for  
this printer. During insertion of the power plug, be sure to hear  
the click to obtain a firm contact.  
CAUTION: Before doing the insertion or extraction of the  
power plug, be sure to pull the outer sleeve of the  
plug backward to release the internal latch.  
Failure to do this could damage the power plug.  
Such damage is considered as an artificial  
destruction and is not covered by the warranty.  
When all the above cable connections are made correctly,  
you may connect your power adaptor to the wall outlet. Make  
sure that the type of power cord and the voltage requirement of  
the power adaptor meet the local power conditions. Do not turn  
the power on for the moment.  
2 - 2  
 
B. LOADING / REPLACING RIBBON  
CASSETTE  
· Turn off the power to the printer.  
· Lift the front end of the top cover  
to remove it.  
· Open the auto cutter by pulling the  
tab up if it is installed in the printer.  
(PP5600B)  
Lift  
Tab  
· Remove slack in the ribbon by  
turning the ribbon feed knob of the  
ribbon cartridge counterclockwise. The  
ribbon must be properly tightened to be  
able to set in position in installation.  
Never turn the knob the other way  
round or the ribbon may mess up inside  
the cassette and ruin the whole  
cassette.  
Fastening  
Knob  
Pressing this end  
· If in process of replacing the  
ribbon cassette, the cassette shall  
be removed in the manner that the  
side of the knob is pulled up first  
with the end of the holding tab  
remain held down.  
Pull up this end to remove  
Seat this end first  
· Place the ribbon cartridge in  
position as shown in the picture.  
Seat the side with the holding tab  
first then press down the whole  
cassette. Rotate the ribbon feed  
knob counterclockwise during the  
action pressing down the ribbon  
cartridge into position to help the  
installation operation if necessary.  
Ribbon feed knob  
2 - 3  
 
· Turn the knob counterclockwise to remove slack in ribbon for  
use.  
· Apply even force  
to close the auto  
cutter (PP5600B)  
so that the small  
lug of auto cutter  
can seat in right  
position on the  
bracket of the  
print mechanism  
as in the picture.  
Î
š
Seat lug outside  
bracket below  
· Close the top cover by fitting its rear end lug first for ribbon  
replacement only or go on loading paper as in next paragraph.  
C. LOADING PAPER  
1. Drop the paper roll inside the paper compartment in the  
orientation as shown in left picture below.  
2. Cut the leading edge of paper roll perpendicular to paper  
direction and now please turn on the  
power to the printer by pressing the  
power button in front side of the  
printer. Insert the leading end of the  
paper roll into the paper intake slot on  
print mechanism. Insert the paper till  
you feel the front end caught by the  
2 - 4  
 
paper feed roller inside the print mechanism then the paper  
will automatically advance to proper position (paper exit of  
print mechanism). In case there was a slip at the insertion of  
the leading end of paper roll and you want to keep same  
heading clearance, you may press the FEED button to  
advance the paper to position.  
3. Close the top cover back. Should the front end of paper roll  
tend to curl as when it comes near end of the paper roll, it is  
advisable to press the FEED button to check if the paper  
comes out of the slot in top cover. Engage manual support to  
make sure it comes out if it fails.  
D. SELF TEST  
Press and hold down the  
feed button while turning on  
the power. The printer will then  
perform a self test and print out  
some major settings detected as  
in picture at right. You may  
turn off the power and turn it  
on again to resume normal use  
of the printer at this stage. You  
may also press the feed button  
at this moment to have the  
printer further print out some  
basic font used and a special  
pattern to have the self test  
proceedings completed as in  
the picture on next page. Please  
note in the first part that both serial and parallel interfaces are  
indicated. That means the printer is working on an auto-sensing  
and auto-select algorithm. The pattern of long vertical lines at  
2 - 5  
 
bottom of the slip is an  
indicator for adjustment on so-  
called bi-directional printing  
offset.  
E. SPECIAL ADJUSTMENTS  
1. Paper near end sensor  
If the paper near end sensor is  
Fixing Screw  
installed in the printer and enabled, a  
fine tuning on the position of the  
paper near end sensor may be  
required for different outer diameter  
of the paper roll bobbin. Please refer  
to the picture at right from inside the  
paper roll compartment that there are  
Sensor Head  
a fixing screw and a sensor head in the wall. Slightly release the  
fixing screw using a blade screw driver or suitable coin to adjust  
the position of sensor head. For smaller roll diameter, the sensor  
head should go lower.  
2. DIP switch setting  
In setup window on bottom plate of  
the printer there are 2 DIP switches. The 4  
position switch at the right is coded S1 and  
controls bi-directional print offset. The 8  
2 - 6  
 
position switch at the left is coded S2 for general printer settings.  
a.Bi-directional printing offset - S1  
Off On Off On Off On Off On Off On Off On Off On Off On  
Off Off On On Off Off On On Off Off On On Off Off On On  
Off Off Off Off On On On On Off Off Off Off On On On On  
Off Off Off Off Off Off Off Off On On On On On On On On  
Pos. 1  
Pos. 2  
Pos. 3  
Pos. 4  
Value  
0
1
2
3
4
5
6
7
8
9 10 11 12 13 14 15  
The offset values in above table are in unit of half dot.  
The bi-directional printing offset actually is well adjusted  
and requires no further action when a new printer is received.  
However, after long period of usage some internal mechanical  
clearance will vary. This clearance can be observed from the  
offset pattern printed in bottom of self test.  
Whenever the lower part of the long vertical lines is shifted  
horizontally away from the upper part by about one dot width, the  
offset value should be adjusted to move it back for decent print if  
bi-directional print is engaged. Increasing the offset value by  
changing the S1 setting can move the lower part to right and  
decreasing the value moves the lower part to left.  
b.Printer general setting – S2  
Switch  
Function  
ON  
OFF  
DTR/DSR  
8-bit data  
No parity check  
Odd parity  
9600  
2-1 Hand shaking mode X-ON/X-OFF  
2-2  
2-3  
2-4  
2-5  
2-6  
Data bit  
Parity check  
Parity selection  
Baud rate (bps)  
Busy on  
7-bit data  
Parity check  
Even parity  
4800  
Buffer full Off line or Buffer full  
Column spacing  
(columns per line)  
Print direction  
2 half dots  
(42 / 35)  
Uni-direction  
3 half dots  
(40 / 33)  
Bi-direction  
2-7  
2-8  
2 - 7  
 
Positions 1 to 6 of the S2 switch define the communication  
protocol and handshaking criteria in RS232 interface. They shall  
always be set to positions 1 to 4 OFF with position 5 set to ON for  
parallel interface application.  
Position 7 of S2 alters the horizontal spacing between  
characters to get different print density on same font format.  
Position 8 of S2 determines whether to print only in one  
direction of print head operation or in both directions.  
All positions of S2 default to OFF when printer delivered.  
3. Wall mount application  
In wall mount application, the paper near end sensor will  
not have proper operation and it is suggested not to install it.  
2 - 8  
 
III. MAINTENANCE GUIDES  
A. MAINTENANCE GUIDE LINES  
Always turn off and disconnect power before start.  
Please pay attention not to be hurt by any sharp edge of the  
metal parts when handling the interior of the printer.  
Do not touch the print head and motor after printing.  
It can become very hot.  
Never use benzene, benzine, thinner, trichloroethylene  
alcohol, or ketone based solvents on the printer’ s plastic and  
rubber components.  
B. GENERAL CLEANING  
Please use a soft hair brush or compressed air to clear away  
any dust or paper scraps accumulation inside the printer. Check  
also the area of the auto-cutter regularly.  
C. TROUBLE SHOOTING  
This section gives solutions to some printer problems you  
may have.  
1. General Problems  
No LED lights up on control panel when switched on –  
Make sure that the power supply cables are correctly plugged into  
the printer, the power adaptor and to the power outlet. Make sure  
that power is supplied to the power outlet. If the power outlet is  
controlled by a switch or timer, try use another outlet.  
3 - 1  
 
2. Printing Problems  
Nothing can be printed with ERROR LED ON – Check  
the Paper Out LED. If it is ON, most probably the paper roll is not  
installed or is at or near the end. Install a new paper roll. If the  
Paper Out LED is OFF, please check for paper jam described in  
next item.  
If there is no paper jam and the printer has been printing for  
quite a period of time, the print head may be overheated. It will  
usually cool back in few minutes and the printing will resume.  
If there is no paper jam and the print head is not overheated,  
turn off the printer and wait for half a minute then turn it back on.  
If the problem still remains, contact a qualified service person.  
Nothing can be printed with ERROR LED OFF – Try to  
run self test according to previous chapter to check if the printer  
itself works properly. If the self test passes, check the following:  
a. Check the connection of the interface cable at both the  
printer and computer ends. Also make sure that this cable  
meets the specification required for both the printer and  
the computer and also the settings by software.  
b.Check the printer data communication settings against the  
computer. The printer settings can be found easily on the  
self test print out.  
If the problem remains or the self test fails, contact your  
dealer or a qualified service person.  
Poor printing quality – Contaminants like paper scraps and  
dusts on the print head or near worn out inked ribbon can lower  
the print quality drastically. Clean the print head replace the  
ribbon cassette as required.  
3 - 2  
 
3. Paper Jam Problems  
Paper is jammed inside the printer – Please follow  
procedures below.  
Do not touch the print head and motor after printing.  
It can become very hot.  
· Turn off the printer.  
· Open the top cover after the print head cools down.  
· Cut the paper roll from the paper intake slot with a pair of  
scissors.  
· Open the auto cutter by pulling the tab up if it is installed in the  
printer. (PP5600B)  
· Turn the printer power back to on.  
· Press the FEED switch to forward the paper out of the paper  
guide. Engage mechanical help like tweezers or manual pull if  
necessary.  
· Clean the paper path when necessary.  
· Reload the paper as instructed in “LOADING PAPER”.  
If the auto cutter is jammed, you may have difficulty  
opening the auto cutter. Please first resolve the auto cutter  
problems per description in next item and then come back to deal  
with the paper jam. Please also clear away any contaminants  
accumulated in the cutter track.  
4. Auto Cutter Problems  
If any materials like a staple or paper clip or excessive paper  
scraps fall into the auto cutter unit, the auto cutter could get stuck.  
In such case, please open the top cover and find adjustment  
window in the auto cutter as shown in the picture on top of  
following page. Please apply a small cross head screw driver to  
turn the plastic screw in the window and to move the cutter blade  
along the track and reset it to home position.  
3 - 3  
 
Auto Cutter Adjustment Window  
To check for home position of the auto cutter, please open  
the auto cutter and look into the blade slot and the spindle hole as  
in pictures below. Use proper tool to cut away the paper around  
auto cutter if it presents obstacle to the actions. Clear away any  
paper scraps from the auto cutter once it is reset to position.  
Blade Slot  
Î
š
Retract blade from the slot  
Move  
spindle  
down  
Î
š
Spindle Hole  
In case it is the auto cutter that fails to respond to the paper  
cut command, please contact your dealer or a qualified service  
person. However, please use manual cutter as a temporary  
alternative measure before this problem is remedied.  
3 - 4  
 
IV. SPECIFICATIONS  
A. PRINTER  
ITEM  
SPECIFICATION  
Printing method  
Print head configuration  
Printing direction  
Effective printing width  
Printing speed (max.)  
Paper feed method  
Paper load method  
Manual cutter  
Dot matrix impact method  
9 pins  
Bi-directional; logic seeking  
59.85 mm  
4.0 lines / sec @ 42 columns  
Friction auto-feed  
Drop and auto paper feed  
Saw tooth blade  
Auto-cutter capability  
Dot Pitch  
Partial cut (1 point at center left)  
0.30 (H) x 0.353 (V) mm  
0.176 mm (1/144 inches)  
Min. 8 N (816 gf)  
140 mm / sec  
DC  
Paper feed pitch (min.)  
Paper feed holding force  
Paper feed speed (max.)  
Input power type  
Input voltage  
24 V + / - 5 %  
Power consumption  
Dimension (mm)  
Weight  
43 W @ printing  
228 (D) x 158 (W) x 140 (H)  
1.6 Kg net (1.9 Kg w/ auto cutter)  
B. PAPER  
1 ply regular roll paper up to 3 ply  
non-carbon copy roll paper  
76 + 0 / - 0.5 mm  
Paper type  
Paper width  
Paper roll outer diameter  
Paper roll inner diameter  
82 mm max.  
12 + 1 / - 0 mm  
70 ~ 100 um for 1 ply, 60 ~ 80 um for  
3 plies  
Paper thickness  
4 - 1  
 
C. RIBBON CASSETTE  
ITEM  
REQUIREMENT  
RECOMMENDED TYPE RC200P  
COLOR  
Purple  
RIBBON MATERIAL  
RIBBON WIDTH  
Nylon 66  
13 mm  
CASSETTE DIMENSION 144.4 (W) x 65 (D) x 26.7 (H) mm  
EXPECTED LIFE 3 million characters  
D. POWER ADAPTOR  
ITEM  
REQUIREMENT  
INPUT VOLTAGE  
INPUT FREQUENCY  
INPUT CURRENT  
OUTPUT VOLTAGE  
OUTPUT POWER  
STATIC LOAD  
100 V AC ~ 250 V AC  
50 ~ 60 HZ  
1.5 A MAX. @ 115 V AC  
+ 24 V DC  
52 W MAX.  
0 A ~ 2.2 A  
OUTPUT REGULATION + / - 5 %  
VPP RIPPLE & NOISE  
MTBF  
240 mV  
30,000 HRS  
EMI STANDARDS  
VDE – B, FCC – B, VCCI – B  
4 - 2  
 

Paxar Printer 9430R User Manual
Pelco Home Theater Server C907M A User Manual
Pelco Marine Instruments PSKIT8100 User Manual
Pelco Security Camera C2423M 5 00 User Manual
Pentax Digital Camera SF1n User Manual
Polycom Webcam V500 User Manual
Printronix Printer L5535 User Manual
PVI Industries Water Heater 1000 N 600A TPL User Manual
PYLE Audio Computer Monitor PLTV75DIN User Manual
PYLE Audio Speaker PAHT4 User Manual